JANE SLOUCHY HAT AND COLLAR | 18 INCH DOLL SET

This pattern set is to make a Jane Slouchy Hat and Collar for American Girl or similar 18 inch Doll. The hat and collar are worked in rounds from bottom to top. Easily knitted, stylish Doll Hat Set.


DISCLOSURE   This post contains affiliate links. If you choose to purchase the product or service via my affiliate link, I will get a small commission. This is at no extra cost to you, but it helps me to run this site. Buying the materials necessary to create new designs, and subsequently sharing it with you. I only recommend products that I like, and have used myself. Thank you for your support.


SKILL LEVEL
Easy

MATERIALS


FINISHED MEASUREMENTS
Hat – 11.0” around, 5.0” tall; For any doll with 12.0” head circumference;
Collar – 11.0” cowl neck circumference, 15.0” bottom circumference,  5.25” length;

GAUGE
21 sts and 28 rows to 4”/10 cm over Raised Relief Pat.
Note: Be sure to check your gauge before starting to knit. If the gauge is larger, change to a smaller needle size. If it is smaller, change to a larger needle size.

INSTRUCTIONS
Notes:

  1. The hat and collar are worked in rounds from bottom to top.
  2. Begin working with circular needle, then change to dpns when necessary.
  3. To avoid mistake(s), count stitches in each round when finished.

HAT

Loosely cast on 56 sts. Join, being careful not to twist sts. Place marker for beg of rnd.

Rnd 1: * K1, p1; repeat from * around – 56 sts.

Repeat Rnd 1 for 1.0” / 2.5 cm, then begin work on Rnd 1 of Raised Relief Pat


Raised Relief Pattern

Rnd 1: * K1, p1; rep from * around – 56 sts.

Rnd 2: Purl – 56 sts.


Repeat rnds 1-2 for Raised Relief Pat until hat measures approx 3.5 inches / 9.0 cm from beg, ending with Rnd 1.

Next (Dec) Rnd: * P5, p2tog; rep from * around – 48 sts.

Next Rnd: * K1, p1; rep from * around – 48 sts.

Next (Dec) Rnd: * P4, p2tog; rep from * around – 40 sts.

Next Rnd: * K1, p1; rep from * around – 40 sts.

Next (Dec) Rnd: * P3, p2tog; rep from * around – 32 sts.

Next Rnd: * K1, p1; rep from * around – 32 sts.

Next (Dec) Rnd: * P2, p2tog; rep from * around – 24 sts.

Next Rnd: * K1, p1; rep from * around – 24 sts.

Next (Dec) Rnd: (P2tog) around – 12 sts.

Cut yarn, leaving a long yarn tail.  Thread tail through remaining sts and gather tightly together.
Fasten off. Secure yarn to WS.

FINISHING
Sew button to Hat.


COLLAR

Note: The collar is worked in rounds from bottom to top (cowl neck).

Loosely cast on 80 sts. Join, being careful not to twist sts. Place marker for beg of rnd.

Rnd 1: * K1, p1; rep from * around – 80 sts.

Repeat Rnd 1 for 1.0” / 2.5 cm, then begin work on Rnd 1 of Raised Relief Pat


Raised Relief Pattern

Rnd 1: * K1, p1; rep from * around – 80 sts.

Rnd 2: Purl – 80 sts.


Repeat rnds 1-2 for Raised Relief Pat until collar measures approx 2.5 inches / 6.5cm from beg, ending with Rnd 1.

Next (Dec) Rnd: * P2, p2tog; rep from * around – 60 sts.

Next Rnd: * K1, p1; rep from * around – 60 sts.

Work in k1, p1 ribbing until collar measures approx 5.25 inches / 13.5 cm from beg.

Bind off all sts loosely in purl.


STITCH ABBREVIATIONS 

approx – approximately;   beg – beginning; dec- decrease(ing); dpn – double-pointed needle(s); k – knit; k2tog – knit two stitches together; lp(s) – loop(s); oz – ounce(s); p – purl; rem – remain/remaining; rep – repeat(s); Rnd(s)- round(s); RS – right side; sl – slip; st(s) – stitch(es); St st – Stockinette stitch; tog – together; WS – wrong side; () – work instructions between parentheses, in the place directed; * – repeat instructions following the single asterisk as directed;  ” – inch(es);

You may get the PDF pattern here

© Alena’s Design

© Alena’s Design patterns are protected by copyright. You may not rewrite, photocopy, redistribute, or sell the patterns in any form. You have my permission to sell the finished product if you will credit me for the pattern with a link to my site:  https://www.alenasdesign.com/ when listing or selling the items made from patterns. If you need any help with my patterns, you may contact me: www.www.alenasdesign.com/contact-us

Newsletter Updates

Subscribe to receive our latest newsletter on your email address.

Leave a Reply

Your email address will not be published. Required fields are marked *